Diamond Table and Depth Percentages Explained
Diamond table and depth percentages describe two proportions of a stone: how wide the flat top facet is, and how tall the diamond is, each measured against the diamond's width. A grading report lists both numbers, and together they hint at how a diamond will handle light. They do not decide cut quality on their own, though, and the best range depends on the shape.
This guide explains what each percentage means, which ranges are commonly seen on well-cut round diamonds, why a stone can look good on paper and still appear dull, and how to read the numbers alongside the rest of a report. For the full picture of cut, color, clarity, and carat weight, start with our 4 Cs guide.
Quick Answer: Table and Depth Percentages at a Glance
Table percentage is the width of the top facet divided by the diamond's average width, and depth percentage is the diamond's total height divided by that same width. For round diamonds, commonly cited ranges run roughly 53% to 62% for table and 59% to 63% for depth, but the cut grade weighs several other angles too.
| Item | What to know |
|---|---|
| Table percentage | Width of the flat top facet compared with the stone's average width |
| Depth percentage | Total height from table to culet compared with the stone's average width |
| Common round table range | Roughly 53% to 62%, depending on crown angle |
| Common round depth range | Roughly 59% to 63%, depending on pavilion angle |
| Too shallow | Light can escape through the bottom, so the stone may look washed out |
| Too deep | More weight sits below the girdle, so the face can look smaller |
What Does Table Percentage Mean on a Diamond?
Table percentage compares the width of a diamond's flat top facet, called the table, with the stone's average width at the girdle. A 57% table, for example, means the top facet spans 57% of the diameter. You can read more about how reports present these measurements on our diamond education page.
The table is the main window light passes through. A larger table can give a bright, open look with broad flashes, while a smaller table sends more light through the crown facets, which often reads as fire, the colorful flashes you see when a diamond moves. Neither is automatically better. The table works together with the crown angle and the star facet length, so a 54% table paired with one crown angle can look quite different from the same table paired with another. Round diamonds with excellent cut grades are commonly reported with tables from the low 50s to the low 60s, which is a general guide rather than a rule.
What Does Depth Percentage Mean on a Diamond?
Depth percentage compares a diamond's total height, measured from the table down to the culet at the bottom point, with its average width. A round diamond that measures 6.5 mm across and 4.0 mm tall has a depth of about 61.5%.
Depth matters because it controls how much of the stone sits below the girdle, where light is meant to reflect internally and return through the top. Many well-cut rounds fall in the low 60s, and some graded Excellent land a little above or below that. Depth also affects price and appearance together. Carat weight is mass, not face-up size, so extra depth adds weight without adding width. Two diamonds of the same carat weight can therefore look noticeably different in size, and the deeper one may cost more per visible millimeter. That is why depth is worth checking before comparing prices.
Key Things to Know
The Percentages Do Not Set the Cut Grade Alone
A cut grade reflects many factors: table, depth, crown angle, pavilion angle, girdle thickness, symmetry, and polish. A diamond can fall inside a familiar table and depth range and still earn a lower grade because its angles are mismatched. The reverse also happens, with a stone sitting slightly outside a commonly cited range yet grading well because its angles balance each other. Treat the two percentages as a quick screening step, then read the full proportions diagram.
Shallow and Deep Stones Behave Differently
A shallow diamond can look wide for its weight, but light may leak out the bottom, leaving a flat or glassy center sometimes called a fish-eye. A deep diamond keeps more light inside, yet it can look dark in places and smaller from above than its weight suggests. Moderate proportions usually balance spread, sparkle, and weight, though some buyers prefer a slightly wider look and accept a small trade-off in brilliance.
Fancy Shapes Follow Different Guidelines
The ranges above apply to round brilliants. Ovals, cushions, emerald cuts, pears, and marquise cuts each have their own proportions, and GIA does not assign an overall cut grade to most of them. Elongated shapes can also show a bow-tie, a darker band across the center. For these shapes, the numbers are less predictable, and seeing the stone in person tells you more than a table percentage can.
Where the Numbers Appear on a Report
On a GIA report, table and depth sit in the proportions section along with the crown angle, pavilion angle, star length, lower-half length, and girdle description. Reading them as a group is more useful than reading them one at a time. If two diamonds share the same grades, a side-by-side look at their proportions often explains why one appears livelier than the other.
How to Choose
Start by deciding which matters more to you: face-up size, brightness, or a balance of both. A wider table and moderate depth can favor spread, while slightly smaller tables with moderate depth often favor fire. Then confirm the choice with the full report, not the two percentages alone. Our natural diamond guide walks through how the grades fit together.
If the diamond is for a ring, the Custom Ring Builder lets you pair a center stone with a setting, and a jeweler can compare candidate stones under the same lighting so differences in proportions become easier to see.
Shop at Buchroeders
Buchroeders offers the Diamond Dollar-for-Dollar Upgrade Privilege on natural diamonds, a lifetime trade-in credit at the full original purchase price toward a diamond upgrade. It does not apply to lab-grown diamonds. Natural diamonds are also sourced through the Diamond Banc network, which gives access to GIA-certified stones at a price advantage. Browse natural diamond engagement rings or schedule an appointment to compare stones side by side.
Frequently Asked Questions
What is a good table percentage for a diamond?
For round diamonds, many well-cut stones fall roughly between 53% and 62%. A number in that range is a starting point, not a guarantee. Crown angle, pavilion angle, and polish all influence how the table performs, so review the full cut grade as well.
What is a good depth percentage for a round diamond?
Many well-cut round diamonds measure in the low 60s, often cited as about 59% to 63%. Depth works together with the pavilion angle, so two stones with the same depth can still return light differently. Ask to see the stone in person.
Does a deeper diamond look smaller?
It can. Extra depth adds carat weight below the girdle without widening the diamond, so a very deep stone may face up smaller than a shallower stone of the same weight. A slightly lower depth often spreads the same weight across a wider face.
Do table and depth matter for fancy shapes?
Yes, though the ideal ranges differ by shape, and GIA does not assign an overall cut grade to most fancy shapes. Ovals, pears, and marquise cuts can also show a bow-tie shadow. Comparing stones in person is the most reliable way to judge them.
Can a diamond have ideal numbers and still look dull?
Yes. Table and depth are only two measurements. Crown and pavilion angles, symmetry, polish, and even a heavy inclusion or tint can affect brilliance. Viewing a diamond in several lighting conditions helps confirm what the report suggests.
What is the Diamond Dollar-for-Dollar Upgrade Privilege?
It is a lifetime trade-in credit at the full original purchase price toward a diamond upgrade at Buchroeders. It applies to natural diamonds only and does not apply to lab-grown diamonds. It lets a buyer move to a larger or higher-quality natural stone later.
Final Thoughts
Table and depth percentages are useful clues, but they are not a verdict. A well-proportioned diamond balances the two with the right angles, good symmetry, and polish, and the best choice depends on whether you value spread, fire, or weight. There is no single ideal number for every buyer or every shape.
Stop by our Columbia showroom or call us at (573) 443-1457 to learn more in person.
